Ash Gel Earthing Electrode
Maintenance-free dual-pipe electrode with conductive gel fill — available in Ash-19, Ash-39, Ash-50, and Ash-60.
Ash Gel Earthing Electrode uses a dual-pipe protection design — an ISI-marked G.I. or copper pipe filled with Ash Back-Fill Compound, a hygroscopic conductive gel. This eliminates the two main failure points of traditional earthing: direct soil contact (which causes corrosion) and drifting ohmic resistance over time.
Key Features
- Highly reliable for safety of human life
- High load carrying capacity and maximum fault current dissipation instantly
- Maintains low resistance value for a long period with bare minimum fluctuation
- Proper galvanization and highly conductive
- Corrosion-free, eco-friendly solution
- Can be used in grid form (3 or more electrodes in equilateral triangle configuration) for large surface-area or highly sensitive installations
- Manufactured as per IS: 3043-1987 requirement
Technical Specifications
Technical Specification
| Code No. | Length (L) mm | Outer Dia (D2) mm approx | Internal Dia (D1) mm approx | Internal Copper Strips | Terminal (T1 & T2) Point (Dia mm) | M.O.C. |
|---|---|---|---|---|---|---|
| Ash-19/2 | 2000 | 46-50 | 22-25 | — | 12 | G.I. |
| Ash-19/3 | 3000 | 46-50 | 22-25 | — | 12 | G.I. |
| Ash-39/2 | 2000 | 76-80 | 37-40 | — | 14 | G.I. |
| Ash-39/3 | 3000 | 76-80 | 37-40 | — | 14 | G.I. |
| Ash-50/2 | 2000 | 47-50 | — | 40×3 | 12 | Copper |
| Ash-50/3 | 3000 | 47-50 | — | 40×3 | 12 | Copper |
| Ash-60/2 | 2000 | 60-63 | — | 50×3 | 12 | Copper |
| Ash-60/3 | 3000 | 60-63 | — | 50×3 | 12 | Copper |
| Ash Spl-2 | 2000 | 17.2 | NA | NA | NA | Cu. Bonded (UL Certified) |
| Ash Spl-3 | 3000 | 17.2 | NA | NA | NA | Cu. Bonded (UL Certified) |
Maximum Surface Area (approx.)
| Code | Length 2000mm | Length 3000mm |
|---|---|---|
| Ash-19 | 3,14,000 sq.mm | 4,71,000 sq.mm |
| Ash-39 | 5,02,400 sq.mm | 7,53,600 sq.mm |
| Ash-60 | 3,95,640 sq.mm | 5,93,460 sq.mm |
| Ash-50 | 3,14,000 sq.mm | 4,71,000 sq.mm |
Installation Guidelines
- 1Recommended for installation in clay or highly humid soil.
- 2Make a pit 6-8 inch diameter, to the appropriate electrode length (2 or 3 metres).
- 3Position the electrode vertically with the terminal on top.
- 4Fill the pit with Ash back-fill compound around the electrode, with proper water pouring simultaneously.
- 5Normally 2 bags of back-fill compound are recommended per electrode (varies in rocky areas).
- 6Connect equipment earthing wire/strip to the terminal using a suitable copper joint.
- 7Fit the chamber cover, and apply petroleum jelly on the exposed terminal.
- 8Continue water pouring for 6-7 days after installation.
Certifications
ISO 9001:2008 CertifiedCPRI Tested (Bhopal)RDSO Tested (Lucknow)
Ready to get started?
Leave your number and our team will reach out.